Recent Posts

Pages: 1 ... 6 7 [8] 9 10

Kaon KSF-570 / Lost some channels (TV3,C4 etc..) !! Retuning instructions for your KSF-570

« Last post by admin on July 04, 2012, 10:47:26 am »

Please use the following instructions to re-tune your receiver:

1. Press Menu
2. Select Installation and press the OK button
3. Enter PIN if requested. Default PIN is 0000
4. Highlight "Optus D1" satellite
5. Write down the value for LNB Freq. You will need this later.
6. Press MENU to go back to the previous screen
7. Select System Settings press OK
8. Enter PIN if requested. Default PIN is 0000
9. Move down to Factory Reset
10. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
11. Select Menu Language and press OK
12. Select Audio Language and press OK
13. Select Subtitle Language and press OK
14. Set the Time to GMT+12:00 and press OK ( we are currently GMT+12:00 and during daylight savings GMT+13:00 )
15. Select the closes location from the list and press OK
16. Press OK on Channel Search
17. Highlight "Optus D1" satellite
18. On the right hand side, if the LNB Freq value is different to what you wrote down, navigate to LNB Freq and press OK to get a popup to select the correct value.
19. Press the GREEN button to show the Transponder List
20. Highlight Transponder "001. 12483 22500 H" and press the OK button. A tick will appear next to it.
21. Press the RED button to show the scan popup
22. Change the "Network" setting to ON
23. Press OK to search
24. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
25. Press OK to exit
26. Press OK to Save the channels found
27. Press Exit to exit the Menu
28. Check if you have all the channels.

Kaon KPSF-200 / Retuning instructions for your KPSF-200 Rev2

« Last post by admin on July 04, 2012, 10:46:04 am »

Please use the following instructions to re-tune your receiver:

1. Press Menu
2. Select System Settings press OK
3. Enter PIN if requested. Default PIN is 0000
4. Move down to Factory Reset
5. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
6. Select Menu Language and press OK
7. Select Audio Language and press OK
8. Select Subtitle Language and press OK
9. Set the Time to GMT+12:00 and press OK ( we are currently GMT+12:00 and during daylight savings GMT+13:00 )
10. Select the closest location from the list and press OK
11. Select "Automatic Freeview Installation"
12. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
13. Press OK to exit
14. Press OK to Save the channels found
15. Press Exit to exit the Menu
16. Check if you have all the channels.

Kaon KPSF-200 / Retuning instructions for your KPSF-200 Rev1

« Last post by admin on July 04, 2012, 10:45:43 am »

Kaon KSF-620R2 / Retuning instructions for your KSF-620R2

« Last post by admin on July 04, 2012, 10:33:18 am »

Puse the following instructions to re-tune your receiver:

1. Press Menu
2. Select Installation and press the OK button
3. Enter PIN if requested. Default PIN is 0000
4. Highlight "Optus D1" satellite
5. Write down the value for LNB Freq. You will need this later.
6. Press MENU to go back to the previous screen
7. Select System Settings press OK
8. Enter PIN if requested. Default PIN is 0000
9. Move down to Factory Reset
10. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
11. Select Menu Language and press OK
12. Select Audio Language and press OK
13. Select Subtitle Language and press OK
14. Set the Time to GMT+12:00 and press OK ( NZ timezone is GMT+12:00 and during daylight savings GMT+13:00 )
15. Select the closes location from the list and press OK
16. Press OK on Channel Search
17. Highlight "Optus D1" satellite
18. On the right hand side, if the LNB Freq value is different to what you wrote down, navigate to LNB Freq and press OK to get a popup to select the correct value.
19. Press the GREEN button to show the Transponder List
20. Highlight Transponder "001. 12483 22500 H" and press the OK button. A tick will appear next to it.
21. Press the RED button to show the scan popup
22. Change the "Network" setting to ON
23. Change Search Type to FTA
24. Press OK to search
25. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
26. Press OK to exit
27. Press OK to Save the channels found
28. Press Exit to exit the Menu
29. Check if you have all the channels.

Kaon KSF-200 / Retuning instructions for your KSF-200 - Prime, Four Plus 1, The Edge TV

« Last post by admin on July 04, 2012, 10:31:05 am »

There was a change put in yesterday that affected several receivers. If you have lost some channels in particular TV3,C4 and Prime, please use the following instructions to re-tune your receiver:

1. Press Menu
2. Select Installation and press the OK button
3. Enter PIN if requested. Default PIN is 0000
4. Highlight "Optus D1" satellite
5. Write down the value for LNB Freq. You will need this later.
6. Press MENU to go back to the previous screen
7. Select System Settings press OK
8. Enter PIN if requested. Default PIN is 0000
9. Move down to Factory Reset
10. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
11. Select Menu Language and press OK
12. Select Audio Language and press OK
13. Select Subtitle Language and press OK
14. Set the Time to GMT+12:00 and press OK ( we are currently GMT+12:00 and during daylight savings GMT+13:00 )
15. Select the closes location from the list and press OK
16. Press OK on Channel Search
17. Highlight "Optus D1" satellite
18. On the right hand side, if the LNB Freq value is different to what you wrote down, navigate to LNB Freq and press OK to get a popup to select the correct value.
19. Press the GREEN button to show the Transponder List
20. Highlight Transponder "001. 12483 22500 H" and press the OK button. A tick will appear next to it.
21. Press the RED button to show the scan popup
22. Change the "Network" setting to ON
23. Change Search Type to FTA
24. Press OK to search
25. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
26. Press OK to exit
27. Press OK to Save the channels found
28. Press Exit to exit the Menu
29. Check if you have all the channels.

Vantage HD6000T/NZ / Retuning Channels after transmission changes

« Last post by admin on June 19, 2012, 08:53:07 pm »

Hi,

If you have a Vantage HD6000/NZ, we suggest that before you retune all the channels, please delete all existing channels and then restart your machine. The receiver will then allow you to rescan the channels.

AH

DTVS-DSR2 / Media Not Live

« Last post by admin on June 16, 2012, 12:25:50 pm »

Some users have advised they are getting "Media not live" when attempting to play back their recordings. the "Media not live" message will appear when the internal HDD is not initialised. This can happen when:

1) The "Safe Remove" option has been done. This option is designed to isolate the HDD and will make the HDD unavailable for recording or playback.

2) The power to the receiver has been turned off and the HDD has not initialised properly.

To recover from this error, please do the following:

1) Power down the receiver by using the power switch at the back of the unit.
2) After about one minute. Turn power on to the receiver.
3) On your TV a message will appear "USB Initialising". Do not press any buttons on your remote.
4) Wait until "USB Ready" message appears. This message will stay for a very short duration.
5) Check your Play List and see if it will appear.

If you still get "Media not live", please contact our help desk on 04 9745031 for further assistance.

AH

Kaon KSF-570 / Instructions for Tuning

« Last post by admin on February 02, 2012, 01:54:18 pm »

Please check the following link for instructions:

https://www.asoft.co.nz/kaon/ksf570.htm

DTVS-T1 / Recording via USB

« Last post by admin on January 24, 2012, 09:16:57 am »

With the DTVS-T1, you can attach a USB memory key or a USB Hard Disk Drive and enable the receiver to record television programmes. After attaching the USB memory key or HDD, you must format the media via the receiver to enable recording. The format process will delete everything on the attached USB memory key or HDD and will prepare your device to allow recording. To do this, please follow these steps:

a) Attach the USB memory key or USB HDD to the receiver.
b) Navigate to Media Manager.
c) Select Media Information
d) Select "Format" drive by pressing the RED button.
e) The receiver will prompt you for a password. The default password is 0000
f) Enter the password and proceed.
g) Please wait for the format to complete. This can take some time and depends on the size of the USB device attached.
h) Once complete, the USB device will show as "Proprietary"

Some more information:
1) Once you have formatted the USB device on the receiver, please do not attempt to view contents on a PC. You may lose the contents as teh format is different.
2) Recordings made on the DTVS-T1 can only be played back on a DTVS-T1.
3) You can only record two channels at a time on the same multiplexer and watch one on the same multiplexer.

AH

DTVS-DSR1 / Recording to USB drive

« Last post by admin on January 24, 2012, 09:13:37 am »

With the DTVS-DSR1, you can attach a USB memory key or a USB Hard Disk Drive and enable the receiver to record television programmes. After attaching the USB memory key or HDD, you must format the media via the receiver to enable recording. The format process will delete everything on the attached USB memory key or HDD and will prepare your device to allow recording. To do this, please follow these steps:

a) Attach the USB memory key or USB HDD to the receiver.
b) Navigate to Media Manager.
c) Select Media Information
d) Select "Format" drive by pressing the RED button.
e) The receiver will prompt you for a password. The default password is 0000
f) Enter the password and proceed.
g) Please wait for the format to complete. This can take some time and depends on the size of the USB device attached.
h) Once complete, the USB device will show as "Proprietary"

Some more information:
1) Once you have formatted the USB device on the receiver, please do not attempt to view contents on a PC. You may lose the contents as teh format is different.
2) Recordings made on the DTVS-DSR1 can only be played back on a DTVS-DSR1.
3) You can only record one channel at a time and what you are watching.

AH