Recent Posts

Pages: 1 [2] 3 4 ... 10

DTVS-1B / Adding Prime Plus 1 to the DTVS-1B, DTVS-1, DTVS-P1, DTVS-P2

« Last post by admin on February 14, 2017, 01:43:03 pm »

Please use the following instructions to add "Prime Plus 1" to the DTVS-1B, DTVS-1, DTVS-P1 & DTVS-P2. Please note that this is not a Freeview channel and hence will not tune automatically on a Freeview receiver following the Freeview guidelines. It has to be added manually. Also, there is no guarantee that this channel will remain in its current free state. It is entire up to Sky to allow access.

The following are the steps to add the channel:

1. Change channel to PRIME (Channel 10)
2. Press the MENU button
3. Select CHANNEL MANAGER
4. Select ADD NEW CHANNEL
5. Move down to "Prime" and press the right arrow to edit the name
6. Change the name to "Prime PL1" (note: Prime Plus 1 may not fit so you will have to enter a shorter name)
7. Move down to VPID and enter 1002 (do not press OK)
8. Move down to APID and enter 1102 (do not press OK)
9. Move down to PCRPID and enter 1002 and then press OK

After completing. Exit the menu by pressing the EXIT button until you are completely out of the menu. Press the OK button to show the Quick Select List and scroll down to your new channel.

DTVS-SMART1 / DTVS-Smart1 - How to manually tune in Freeview channels

« Last post by admin on November 11, 2016, 02:41:14 pm »

It appears that after some changes in transmission, the DTVS-Smart1 is unable to automatically set up the Freeview channels at initial setup. You can skip the channel search if it fails and use the manual tuning method described below to tune the channels:

1. Press the MENU button
2. Select "Setup" and press OK
3. Enter PIN. Default PIN is 0000
4. Select "Channel Search" and press OK
5. Select "Optus D1" satellite on the left
6. Press the GREEN button to Edit Satellite
7. Move to "LNB Frequency" and press OK to show the LNB list
8. From the list select the LNB Frequency of your LNB on the dish. Most common values are 10750, 11300. Try 10750 if you have a Sky dish
9. Press the Back button to return to previous screen
10. Move to the "Transponder list" on the right and find the transponder with frequency 12456
11. Press the OK button. When selected, you will see a blue marker on the left of the frequency
12. Press the RED button to show the Search window
13. Select NIT Search as YES
14. Select Search Type as FTA
15. Press OK to search
16. Once the search is complete, press the OK button to save the search results
17. Press the BACK button to exit the menu

DTVS-SMART1 / Transfer an Application from your Android Mobile

« Last post by admin on September 08, 2016, 09:45:57 am »

You can transfer an Android application from your Android mobile to the DTVS-SMART1 via the DTVS-SMART1 Android Remote Control application.

The DTVS-SMART1 Android Remote Control application can be downloaded to your Android Smartphone via the Google Playstore. Search the Google Playstore for iSmartRCU by Innodigital Inc.

The iSmartRCU connects to the DTVS-Smart1 via the local network and can be used to transfer an Android application from your phone to the DTVS-SMART1 via the "Transfer Application" option. When transferring an application, please ensure that the application your are transferring will work on Android version 4.0.3.

DTVS-SMART1 / Freeview Channels Changes - Prime, Four Plus 1, The Edge TV moving frequency

« Last post by admin on May 25, 2016, 12:50:24 pm »

You can update the DTVS-Smart1 via two methods.

1) Download the USB data file and upgrade. Details via the following link:
https://www.dtvs.co.nz/forum/index.php?topic=232.0

or follow the manual channel search method:

1. Press the MENU button
2. Select SETUP
3. Enter the PIN. Default PIN is 0000
4. Select CHANNEL SEARCH
5. Press the BLUE button to select delete channels
6. Select )K to delete channels
7. Move across and down the transponder list to 12483MHz
8. Press OK on 12483MHz. A green bar will light up on the left
9. Press the RED button to bring up the search options
10. Select NIT and FTA and press OK
11. Press OK to save the channels
12. Press the BACK button three times to exit the menu.

DTVS-P2 / Freeview Channels Changes - Prime, Four Plus 1, The Edge TV moving frequency

« Last post by admin on May 24, 2016, 08:24:54 pm »

DTVS-P1 / Freeview Channels Changes - Prime, Four Plus 1, The Edge TV moving frequency

« Last post by admin on May 24, 2016, 08:23:52 pm »

DTVS-1 / Freeview Channels Changes - Prime, Four Plus 1, The Edge TV moving frequency

« Last post by admin on May 24, 2016, 08:19:51 pm »

DTVS-1B / Freeview Channels Changes - Prime, Four Plus 1, The Edge TV moving frequency

« Last post by admin on May 24, 2016, 08:14:20 pm »

Prime, Four Plus 1 and The Edge channels are moving frequency. The easiest way to re-tune the DTVS-1B is to carry out a factory default and the re-tuning your receiver. The following are the steps:

On the DTVS remote control:

1. Press the MENU button
2. Select "Installation" and press the OK button
3. Select "Factory default" and press the OK button
4. Enter the password. The default password is "0000"
5. Select "Yes" and press OK on the question "Do you want to factory reset?"
6. Select your closest location (use the left or right arrow buttons to change the location). They press OK.
7. Select "Yes" and press OK on the question "Do you want to scan?"
8. The receiver will start tuning the channels and will save them automatically

Troubleshooting

1. Database Empty or Tuning Failed
This means your receiver failed to find a signal. This can happen if equipment on your satellite dish
is not sending the signal as expected by the receiver. Try the following:

a) Try tuning the receiver using the following instructions:
https://www.dtvs.co.nz/forum/index.php?topic=263.0

b) If the above gets you the channels, use the following method to remove any unwanted channels:
https://www.dtvs.co.nz/forum/index.php?topic=247.0

2. All channels tuned in but Prime, Four Plus 1, The Edge TV do not tune
Some older units may have issues with tuning due to older software on their receiver. It is possible to add the channels manually via the following instructions:
a) Press the MENU button
b) Select INSTALLATION
c) Select TRANSPONDER SETUP
d) Select ADD
e) Move to Frequency and enter 12519
f) Move to Symbolrate and enter 22500
g) Move to Network and change the value to OFF
h) Press the OK button. The receiver will response "Do you want to scan?"
i) Select Yes to scan
j) Once scanning is complete, the screen will return to the TRANSPONDER SETUP screen
k) Exit the menu by pressing the EXIT button until you see normal TV.

3. If all fails you can contact our technical support number, 0800 388765 or 049745031. If we are unable to take your
call please leave a message or, you can send an email to techsupport@dtvs.co.nz

DTVS-1B / No signal and only two green dots on display

« Last post by admin on May 24, 2016, 08:03:08 pm »

Your DTVS-1B will show the program (channel) number or the time on the display during normal operation. If your receiver is not showing any numbers or letters on the display and shows only two green dots then your receiver has developed a fault. You can send your unit for repair or you may replace it. Repair address is:

DTV Solutions Limited
97 Velino Place
RD2
Kaiapoi 9692

DTVS-SMART1 / XBMC - Missing repository and dependencies not met

« Last post by admin on September 25, 2015, 07:36:32 am »

Due to recent changes some repositories may go missing and plugins may show as "broken". Please contact us via web email or phone 042322957 if you need assistance with XBMC missing repository.